Meth by Shake and bake What do you think of the method and the ingredients? It's my first time.

[ahmad999]

Hello friends
I want to use this method of cooking meth.
I need your advice if there's something wrong
Shak and bak method

Using a 2 liter bottle I will do these steps
1) Add 12,000mg pseudoephedrine after grinding

2) Add 190ml of ammonium nitrate

3) shake the bottle well

4) Add starter fluid (that you will use contains 35% ether and 65% hexane) What do you think is it good?

5) Add 7 grams of lithium (extracted from a battery Energizer Ultimate Lithium )

6) Add 25ml of sodium hydroxide

7) Add two covers of water

8) After the reaction starts, the bottle is vented whenever the pressure is high

9) Add 25ml of sodium hydroxide every 20 minutes to make the reaction continuous

10) Finally, after lithium melts or turns bronze, the reaction is over.

11) Add hydrochloric gas to get meth

I will apply these steps I need your advice are there mistakes It's my first time cooking.
Thank you, waiting for your advice.

 

[Noctis]

yeah i would do more reading before you attempt... search in the search bar and you should be able to find a shit ton of references

 

[Anarchy Labz]

I thought sodium hydroxide was a solid? Do you mean grams?

 

[SoldadoDeDrogas]

That is ALOT of lithium, much more than is necessary, probably a dangerous excess even. 2/3 grams should be enough. I use 2 AA batteries and that is much more than is needed for 5-6g of PSE. 2/3 AA batteries will be more than enough for 12g of PSE.

Ether from starting fluid is good. Paint thinner works great. Naptha, colemans fuel, or any combination of ... virtually any non polar hydrocarbon petroleum distillate will work as solvent. 200-300ml should be good.

190ml or grams? of ammonium nitrate is alot of material also. You shouldn't need more than 40 grams.
Sodium hydroxide you are going to want more of. I would suggest about 2x the amount of AN. So if 40g of AN, use 80g of NaOH.

Lastly add about 5-10ml distilled water. Insert a hose into the bottom of your bottle and put the water in so that it goes past the lithium without reacting. This will kick off the reaction. Get the cap on asap. Burp it after the first minute to get rid of any CO2 inside the bottle. With these ingredients in this quantity in a 2 liter bottle, you shouldn't need to burp much after this initial burp. The reaction shouldn't take longer than an hour. The lithium will turn copper color and dissolve - this is what you are looking for. When the reaction is mostly complete and the Li has been dissolved, burp it to a safe level of pressure and you can shake the shit out of it to expose all the PSE to the lithium and make sure everything is homogenized and reacted thoroughly. Then you may proceed to filtering, base, extract, salt, wash, crystallize etc.

 

[uiawghdouawhdouiawhd]

its best to keep the reaction anhydrous and completely free from water, if the ammonium salt is pure it will react on its own with the sodium hydroxide and you can add gentle heat to get it rolling but not high than 58c,

 

[ahmad999]

Hello friend
I applied the steps and the reaction worked until the lithium completely melted
When the reaction was over, I filtered the liquid.
Then I made hydrochloric gas by (adding 10 g table salt with 20 ml sulfuric acid) Is that right?
After putting the hose in the liquid I got the powder but it immediately melted
I don't know what the problem is.
Please help

 

[uiawghdouawhdouiawhd]

what were u trying to do?

 

[SauceySockss]

What do you mean it immediately "melted"?

 

[SoldadoDeDrogas]

It should be noted that it is best to wait a while after the reaction inbetween steps for the ammonia to evaporate from the solvent. After filtering it is important to dry the reaction liquid with anhydrous epsom salts Mg2SO4. This is important to make sure your product does not "melt" when you gas it. Any moisture will dissolve your product and it will become over acidified instantly. It is best to freeze your reaction liquid as cold as you can before you gas it also to get the most density when gassing.

It sounds like this is your problem. Moisture contamination melted your product. Is there a red layer of liquid at the bottom of your fuel after gassing? I think you can add %20 NaOH solution and re extract with hydrocarbon solvent and dry with epsom salt and try to gas again but do it properly this time and you should salt a good product that doesn't melt. Otherwise perhaps the product has been ruined and you will have to start over.

Also, you may have to make sure the gas is absolutely dry also. Sometimes there is moisture in the gas when you salt out. You can push gas through a tube packed with more epsom salts or you can run gas through another sulfuric acid trap to absorb any moisture before it reaches the product solvent.

 

[SauceySockss]

where are you getting your ammonium nitrate from? I have been using the shit from the instant cold packs at walgreens that has "Calcium Ammonium Nitrate" and followed the rest of your ingredients. When the lithium bronzes, I am able to filter it and gas it at the end. I also get quite a lot of powder from gassing, but its not meth. I dont know what it is but its not dope. I will gas it a second time and get a teeny tiny amount of powder and that will get me like 2-3 hits of "dope" but its absolutely horrible.


I found a different cold pack from CVS that contains "UREA BLEND" would that be better to use instead of the CAN i was getting from the other cold packs? I have no idea where to get AN or how to make it.

 

[uiawghdouawhdouiawhd]

message me